Victron Energy
Victron is a world leader in the supply of self-supporting electrical power. Victron products have been designed to meet the most demanding situations faced by a diversity of craft, recreational and commercial alike. Victron’s ability to meet the demand for customised off-grid systems is unprecedented. Victron’s product range includes sine wave inverters and inverter/chargers, battery chargers, DC/DC converters, transfer switches, gel and AGM batteries, battery monitors, solar charge controllers, solar panels, complete network solutions and many other innovative solutions.
Victron MultiPlus-II 3kVA
Inverter/Charger
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp.
A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land-based off-grid applications. It also has built-in anti-islanding functionality and an increasingly long list of country approvals for ESS applications. Several system configurations are possible.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate for insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off-grid as well as grid-connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no-break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Virtually unlimited power thanks to parallel (not for the 8k, 10k and 15k models) and three-phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed.
PowerControl & PowerAssist: Yes
Transfer switch: 32 A
Maximum AC input current: 32 A
INVERTER
DC Input voltage range: 12V – 9,5–17 V / 24V – 19–33V / 48V – 38-66 V
Output: Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1% (1)
Cont. output power at 25°C (3): 3000 VA
Cont. output power at 25°C: 2400 W
Cont. output power at 40°C: 2200 W
Cont. output power at 65°C: 1700 W
Max apparent feed-in power: 3000 VA
Peak power: 5500 W
Maximum efficiency: 93%/94%/95%
Zero load power: 13 / 13 / 11 W
Zero load power in AES mode: 9 / 9 / 7 W
Zero load power in Search mode: 3 / 3 / 2 W
CHARGER
AC input: Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz
Charge voltage ‘absorption’: 14,4 / 28,8 / 57,6 V
Charge voltage ‘float’: 13,8 / 27,6 / 55,2 V
Storage mode: 13,2 / 26,4 / 52,8 V
Max. battery charge current (4): 120 /70 / 35 A
Battery temperature sensor: Yes
GENERAL
Auxiliary output: Yes (32A)
External AC current sensor (optional): 50A or 100A
Programmable relay (5): Yes
Protection (2): a – g
VE.Bus communication port: For parallel (not for 8k, 10k and 15k models) and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Operating temperature range: -40 to +65°C (fan assisted cooling)
Humidity (non-condensing): max 95%
ENCLOSURE
Protection category: IP22
Battery-connection: M8 bolts
230 V AC-connection: Screw terminals 13 mm² (6 AWG)
Weight: 19 kg
10-Year Limited Warranty.
Victron MultiPlus-II 5kVA
Inverter/Charger
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp.
A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land-based off-grid applications. It also has built-in anti-islanding functionality and an increasingly long list of country approvals for ESS applications. Several system configurations are possible.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate for insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off-grid as well as grid-connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no-break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Virtually unlimited power thanks to parallel (not for the 8k, 10k and 15k models) and three-phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed.
PowerControl & PowerAssist: Yes
Transfer switch: 50 A
Maximum AC input current: 50 A
INVERTER
DC Input voltage range: 12V – 9,5–17 V / 24V – 19–33V / 48V – 38-66 V
Output: Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1% (1)
Cont. output power at 25°C (3): 5000 VA
Cont. output power at 25°C: 4000 W
Cont. output power at 40°C: 3700 W
Cont. output power at 65°C: 3000 W
Max apparent feed-in power: 5000 VA
Peak power: 9000 W
Maximum efficiency: 96%
Zero load power: 18 W
Zero load power in AES mode: 12 W
Zero load power in Search mode: 2 W
CHARGER
AC input: Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz
Charge voltage ‘absorption’: 14,4 / 28,8 / 57,6 V
Charge voltage ‘float’: 13,8 / 27,6 / 55,2 V
Storage mode: 13,2 / 26,4 / 52,8 V
Max. battery charge current (4): 120 /70 A
Battery temperature sensor: Yes
GENERAL
Auxiliary output: Yes (32A)
External AC current sensor (optional): 50A or 100A
Programmable relay (5): Yes
Protection (2): a – g
VE.Bus communication port: For parallel (not for 8k, 10k and 15k models) and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Operating temperature range: -40 to +65°C (fan assisted cooling)
Humidity (non-condensing): max 95%
ENCLOSURE
Protection category: IP22
Battery-connection: M8 bolts
230 V AC-connection: Screw terminals 13 mm² (6 AWG)
Weight: 30 kg
10-Year Limited Warranty.
Victron MultiPlus-II 8kVA
Inverter/Charger
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp.
A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land-based off-grid applications. It also has built-in anti-islanding functionality and an increasingly long list of country approvals for ESS applications. Several system configurations are possible.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate for insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off-grid as well as grid-connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no-break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Virtually unlimited power thanks to parallel (not for the 8k, 10k and 15k models) and three-phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed.
PowerControl & PowerAssist: Yes
Transfer switch: 100 A
Maximum AC input current: 100 A
INVERTER
DC Input voltage range: 12V – 9,5–17 V / 24V – 19–33V / 48V – 38-66 V
Output: Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1% (1)
Cont. output power at 25°C (3): 8000 VA
Cont. output power at 25°C: 6400 W
Cont. output power at 40°C: 5500 W
Cont. output power at 65°C: 4000 W
Max apparent feed-in power: 8000 VA
Peak power: 15000 W
Maximum efficiency: 95%
Zero load power: 29 W
Zero load power in AES mode: 19 W
Zero load power in Search mode: 3 W
CHARGER
AC input: Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz
Charge voltage ‘absorption’: 14,4 / 28,8 / 57,6 V
Charge voltage ‘float’: 13,8 / 27,6 / 55,2 V
Storage mode: 13,2 / 26,4 / 52,8 V
Max. battery charge current (4): 110 A
Battery temperature sensor: Yes
GENERAL
Auxiliary output: Yes (50A)
External AC current sensor (optional): 50A or 100A
Programmable relay (5): Yes
Protection (2): a – g
VE.Bus communication port: For parallel (not for 8k, 10k and 15k models) and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Operating temperature range: -40 to +65°C (fan assisted cooling)
Humidity (non-condensing): max 95%
ENCLOSURE
Protection category: IP22
Battery-connection: M8 bolts (2 plus and 2 minus connections)
230 V AC-connection: Bolts M6
Weight: 42 kg
10-Year Limited Warranty.
Victron MultiPlus-II 10kVA
Inverter/Charger
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp.
A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land-based off-grid applications. It also has built-in anti-islanding functionality and an increasingly long list of country approvals for ESS applications. Several system configurations are possible.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate for insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off-grid as well as grid-connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no-break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Virtually unlimited power thanks to parallel (not for the 8k, 10k and 15k models) and three-phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed.
PowerControl & PowerAssist: Yes
Transfer switch: 100 A
Maximum AC input current: 100 A
INVERTER
DC Input voltage range: 12V – 9,5–17 V / 24V – 19–33V / 48V – 38-66 V
Output: Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1% (1)
Cont. output power at 25°C (3): 10000 VA
Cont. output power at 25°C: 8000 W
Cont. output power at 40°C: 7000 W
Cont. output power at 65°C: 6000 W
Max apparent feed-in power: 10000 VA
Peak power: 18000 W
Maximum efficiency: 96%
Zero load power: 38 W
Zero load power in AES mode: 27 W
Zero load power in Search mode: 4 W
CHARGER
AC input: Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz
Charge voltage ‘absorption’: 14,4 / 28,8 / 57,6 V
Charge voltage ‘float’: 13,8 / 27,6 / 55,2 V
Storage mode: 13,2 / 26,4 / 52,8 V
Max. battery charge current (4): 140 A
Battery temperature sensor: Yes
GENERAL
Auxiliary output: Yes (50A)
External AC current sensor (optional): 50A or 100A
Programmable relay (5): Yes
Protection (2): a – g
VE.Bus communication port: For parallel (not for 8k, 10k and 15k models) and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Operating temperature range: -40 to +65°C (fan assisted cooling)
Humidity (non-condensing): max 95%
ENCLOSURE
Protection category: IP22
Battery-connection: M8 bolts (2 plus and 2 minus connections)
230 V AC-connection: Bolts M6
Weight: 49 kg
10-Year Limited Warranty.
Victron MultiPlus-II 15kVA
Inverter/Charger
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp.
A MultiPlus, plus ESS (Energy Storage System) functionality
The MultiPlus-II is a multifunctional inverter/charger with all the features of the MultiPlus, plus an external current sensor option which extends the PowerControl and PowerAssist function to 50A resp. 100A. The MultiPlus-II is ideally suited for professional marine, yachting, vehicle and land-based off-grid applications. It also has built-in anti-islanding functionality and an increasingly long list of country approvals for ESS applications. Several system configurations are possible.
PowerControl and PowerAssist – Boosting the capacity of the grid or a generator
A maximum grid or generator current can be set. The MultiPlus-II will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function). PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the MultiPlus-II will compensate for insufficient generator, shore or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The MultiPlus-II can be used in off-grid as well as grid-connected PV and other alternative energy systems. It is compatible with both solar charger controllers and grid-tie inverters.
Two AC Outputs
The main output has no-break functionality. The MultiPlus-II takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus-II. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Virtually unlimited power thanks to parallel (not for the 8k, 10k and 15k models) and three-phase operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 48/5000/70 units, for example, will provide 25 kW / 30 kVA output power with 420 Amps charging capacity. In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 1200 Amps charging capacity.
On-site system configuring, monitoring and control
Settings can be changed in a matter of minutes with VEConfigure software (computer or laptop and MK3-USB interface needed). Several monitoring and control options are available: Cerbo GX, Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart dongle), Battery Monitor, Digital Multi Control Panel.
Remote configuring and monitoring
Install a Cerbo GX or other GX product to connect to the internet. Operational data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge. When connected to the internet, systems can be accessed remotely, and settings can be changed.
PowerControl & PowerAssist: Yes
Transfer switch: 100 A
Maximum AC input current: 100 A
INVERTER
DC Input voltage range: 12V – 9,5–17 V / 24V – 19–33V / 48V – 38-66 V
Output: Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1% (1)
Cont. output power at 25°C (3): 15000 VA
Cont. output power at 25°C: 12000 W
Cont. output power at 40°C: 10000 W
Cont. output power at 65°C: 7000 W
Max apparent feed-in power: 15000 VA
Peak power: 27000 W
Maximum efficiency: 95%
Zero load power: 55 W
Zero load power in AES mode: 39 W
Zero load power in Search mode: 6 W
CHARGER
AC input: Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz
Charge voltage ‘absorption’: 14,4 / 28,8 / 57,6 V
Charge voltage ‘float’: 13,8 / 27,6 / 55,2 V
Storage mode: 13,2 / 26,4 / 52,8 V
Max. battery charge current (4): 200 A
Battery temperature sensor: Yes
GENERAL
Auxiliary output: Yes (50A)
External AC current sensor (optional): 50A or 100A
Programmable relay (5): Yes
Protection (2): a – g
VE.Bus communication port: For parallel (not for 8k, 10k and 15k models) and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Operating temperature range: -40 to +65°C (fan assisted cooling)
Humidity (non-condensing): max 95%
ENCLOSURE
Protection category: IP22
Battery-connection: M8 bolts (2 plus and 2 minus connections)
230 V AC-connection: Bolts M6
Weight: 80 kg
10-Year Limited Warranty.
Victron Quattro 10kVA
Inverter/Charger
Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.
Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example, the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.
Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Split phase option
A split-phase AC source can be obtained by connecting our autotransformer.
Three phase capability
Three units can be configured for three-phase output. But that’s not all: up to 4 sets of three 15kVA units can be parallel connected to provide 144kW / 180kVA inverter power and 2400A charging capacity.
PowerControl – Dealing with limited generator, shore side or grid power
The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shoreside supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.
PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The Quattro can be used in off-grid as well as grid-connected PV and other alternative energy systems.
Loss of mains detection software is available.
System configuring
- In the case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure.
- Parallel and three-phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.
- Off-grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).
On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Colour Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Colour Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Colour Control GX or other GX device can be accessed and settings can be changed remotely.
PowerControl & PowerAssist: Yes
Integrated Transfer switch: Yes
AC inputs (2x): Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz / Power factor: 1
Maximum feed through current (A): 2 x 100
INVERTER
DC Input voltage range (V DC): 9,5 – 17V / 19 – 33V / 38 – 66V
Output (1): Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1%
Cont. output power at 25°C (VA) (3): 10000
Cont. output power at 25°C (W): 8000
Cont. output power at 40°C (W): 6500
Cont. output power at 65°C (W): 4500
Peak power (W): 20000
Maximum efficiency (%): 96%
Zero load power (W): 60
Zero load power in AES mode (W): 40
Zero load power in Search mode (W): 15
CHARGER
Charge voltage ‘absorption’ (V DC): 57,6
Charge voltage ‘float’ (V DC): 55,2
Storage mode (V DC): 52,8
Charge current house battery (A) (4): 140
Charge current starter battery (A): 4 (12V and 24V models only)
Battery temperature sensor: Yes
GENERAL
Auxiliary output (A): 50
Programmable relay (6): 3x
Protection (2): a – g
VE.Bus communication port: For parallel and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Common Characteristics: Operating temp.: -40 to +65˚C / max. 95% / Humidity (non-condensing): max. 95%
Maximum altitude: 3500m
ENCLOSURE
Common Characteristics: Material & Colour: aluminium (blue RAL 5012) / Protection category: IP 21
Battery-connection: Four M8 bolts (2 plus and 2 minus connections)
230 V AC-connection: Bolts M6
Weight: 51 kg
10-Year Limited Warranty.
Victron Quattro 15kVA
Inverter/Charger
Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally, it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split-phase operation and parallel operation.
Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example, the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.
Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.
Split phase option
A split-phase AC source can be obtained by connecting our autotransformer.
Three phase capability
Three units can be configured for three-phase output. But that’s not all: up to 4 sets of three 15kVA units can be parallel connected to provide 144kW / 180kVA inverter power and 2400A charging capacity.
PowerControl – Dealing with limited generator, shore side or grid power
The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shoreside supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.
PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The Quattro can be used in off-grid as well as grid-connected PV and other alternative energy systems.
Loss of mains detection software is available.
System configuring
- In the case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure.
- Parallel and three-phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.
- Off-grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).
On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Colour Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Colour Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Colour Control GX or other GX device can be accessed and settings can be changed remotely.
PowerControl & PowerAssist: Yes
Integrated Transfer switch: Yes
AC inputs (2x): Input voltage range: 187-265 VAC / Input frequency: 45 – 65 Hz / Power factor: 1
Maximum feed through current (A): 2 x 100
INVERTER
DC Input voltage range (V DC): 9,5 – 17V / 19 – 33V / 38 – 66V
Output (1): Output voltage: 230 VAC ± 2% / Frequency: 50 Hz ± 0,1%
Cont. output power at 25°C (VA) (3): 15000
Cont. output power at 25°C (W): 12000
Cont. output power at 40°C (W): 10000
Cont. output power at 65°C (W): 7000
Peak power (W): 25000
Maximum efficiency (%): 96%
Zero load power (W): 110
Zero load power in AES mode (W): 75
Zero load power in Search mode (W): 20
CHARGER
Charge voltage ‘absorption’ (V DC): 57,6
Charge voltage ‘float’ (V DC): 55,2
Storage mode (V DC): 52,8
Charge current house battery (A) (4): 200
Charge current starter battery (A): 4 (12V and 24V models only)
Battery temperature sensor: Yes
GENERAL
Auxiliary output (A): 50
Programmable relay (6): 3x
Protection (2): a – g
VE.Bus communication port: For parallel and three-phase operation, remote monitoring and system integration
General purpose com. port: Yes, 2x
Remote on-off: Yes
Common Characteristics: Operating temp.: -40 to +65˚C / max. 95% / Humidity (non-condensing): max. 95%
Maximum altitude: 3500m
ENCLOSURE
Common Characteristics: Material & Colour: aluminium (blue RAL 5012) / Protection category: IP 21
Battery connection: Four M8 bolts (2 plus and 2 minus connections)
230 V AC-connection: Bolts M6
Weight: 72 kg
10-Year Limited Warranty.
Omega Watt Product Range
Product Features and Specifications
We are the approved installers and technical support agents for the following products listed below.
Click to view specifications and information on the products we suggest and use with our Solar Solutions.
